Dear user, thank you for using our company's products. In order to ensure smooth operation of the machine and obtain the most perfect product, please carefully read the operation manual.

1、 Precautions

When the machine is working, it is prohibited to enter its operating area.

The operator stands within reach of the emergency stop switch.

This machine must be operated by a dedicated person.

Please turn off the power when the machine malfunctions.

Keep the machine and environment clean.

For safety reasons, please turn off the power when installing the mold.

Before use, please check the oil level of the oil gauge and maintain it at 2/3 or above of the hydraulic oil gauge position.

Place the machine on a sturdy ground and level it to make it more stable.

Check the direction of the motor, if there is an error in direction, adjust the power supply wiring.

When the machine is in automatic mode, please confirm the accuracy of the input data.

2、 Overview

DW38 single head hydraulic pipe bending machine, is a product developed by our company on the basis of absorbing advanced foreign technology. This product is controlled by a microcomputer, driven by hydraulic pressure, displayed with Chinese subtitles, and operated through human-machine dialogue. It can be operated in manual, semi-automatic, or fully automatic modes at will. The mobile foot switch has both rain start and emergency stop functions, with high safety. The whole machine has stable performance and high bending efficiency, making it an ideal equipment in the pipe processing industry.

IIItechnical data

Maximum bending capacity: Φ38╳2（mm） A3

Maximum bending radius: R200（mm）

Maximum bending angle: 185º

Maximum core length: 1900mm

Motor power: 4kw

Oil pump: PVD-19

System pressure: 12Mpa

Fuel tank capacity: Recommended YA-N46 hydraulic oil for 110L

Bending speed: 65º/sec

specific operation

1. Press the "Parameters" button to enter the parameter setting screen

As shown in the following figure (example)

After setting the S07 bend angle

Then enter the following painting

There are a total of 19 parameters: press the up and down keys to

Move the arrows up and down.

2. Setting instructions:

1. There is a parameter description and setting range at the top right corner of the screen;

When the set parameter is greater than the allowable value, the system replaces it with the maximum allowable value of the parameter, and replaces it with the minimum value when it is less than the minimum allowable value;

When the number of decimal places entered exceeds the allowed multiple, the system will automatically remove the excess multiple without rounding.

3. Setting method:

1. Follow the on-screen prompts and press the up and down keys to move the arrow to select a parameter. The parameter pointed to by the arrow is the selected parameter.

2. Simply press the number keys at the desired input location to enter the parameters:

3. After completing the parameter input, press "confirm" to save the parameters for easy modification; Press' Cancel 'to exit the input state, but still point to this parameter. You can re-enter the parameter.

Parameter Description

S01 part number

Description: Set the part number that needs to be processed. The parameters of each component previously set will be stored in the system and can be directly used by simply setting the corresponding part number. Range: 0-15

02 Workpiece mode:

Explanation: The mode entered after stepping on the foot during manual standby.

Scope: 1-Half (Automatic)/2-Full (Automatic)

S03 Core Rod Operation:

Explanation: Set whether core rod action is required

Scope: 0- None 1- Yes

S04 auxiliary push operation:

Explanation: Set whether auxiliary push actions are required

Scope: 0-open 1-present

S05 bend pipe clamping:

Explanation: During the bending process, the clamping valve remains open.

Scope: 0-on 1-off

S06 number of bends:

Explanation: Set the number of bends required for the workpiece.

Range: 1-16 corners.

S07 bend angle setting:

Explanation: Set all bending angles for the part corresponding to "S01 part number". The number of bending angles for this part is determined by "S06 bending angle quantity". The bending action starts from "W01 bending angle 1" and continues in sequence

W01 Corner 1:

Description: Set the first bend angle

Range: 0-220.0 degrees

S08 bend correction

Explanation: Set the value of angle correction in degrees. This value will reduce the actual bending angle.

Range: 0-20.0 degrees

S09 early core return

Explanation: During the bending process, the set value is set in advance to start the core withdrawal

Range: 0-220 degrees

S10 clamping:

Description: Set clamping time

Range: 0-10 seconds

S11 clip removal:

Description: Set the clip removal time

Range: 0-10 seconds

S12 chip insertion

Description: Set the core insertion time

Range: 0-10 seconds

S13 chip return

Explanation: Set the core return time

Range: 0-10 seconds

S14 holding time

Description: Set the holding time

Range: 0-10 seconds

S15 retrieval time:

Explanation: In fully automatic mode, the time used for picking up workpieces

Range: 0-20 seconds

S16 test interval

Explanation: The time from the end of one test run to the beginning of the next test run

Range: 0-20 seconds

S17 backlight switch:

Explanation: When set to "1", the LCD backlight is always on; When setting '0'

Without pressing any button, it will turn off after 20 seconds, but when any button is pressed, the backlight will turn on.

Scope: 0-off/1-on

S18 set quantity

Explanation: Set the total quantity of parts that need to be processed for a batch

Range: 0-32760

S19 processing quantity

Description: Set/display the quantity of processed parts. If the processing quantity is greater than or equal to the set quantity, the processing will automatically stop.

Range: 0-32760

6、 Operating instructions:

Explanation of Four Modes of Work

◇ "Manual" working mode operation (the initial working mode is "manual" when powered on):

After pressing the "Run" button, enter the manual operation screen and follow the on-screen prompts to operate:

Pressing the corresponding action key can execute various corresponding actions;

2. When manually bending the pipe, stop bending when the first set angle is reached (convenient for mold testing);

3. Oil cylinders with sensors, regardless of whether the manual button is pressed, will stop operating when the sensor sends a signal;

4. When performing clamping and bending operations, the auxiliary push must be fully retracted (there will be corresponding prompts at the bottom of the screen);

◇ "Semi automatic" working mode operation (recommended for normal production):

1: Manually install the work;

2: Stepping on the pedal switch, the automatic clamping work begins, and the automatic bending begins. After the bending angle is equal to the set angle (if there is a correction value, this value should be subtracted from the correction value), the bending action automatically stops and the core is removed;

3: Step on the foot switch to automatically bend and insert the core;

4: At this point, complete a bend. If the corner count is equal to the set number of corners (the last corner), proceed to step six;

5: Corner counting automatically increments by one

Go to the second step and continue bending the next corner;

6: Add one to the workpiece count, manual removal of the workpiece is complete!

◇ Fully automatic explanation:

Fully automatic only allows for bending without the need for foot pedals after taking out the workpiece during the semi-automatic process.

◇ Test instructions: After setting the mode to test, press the foot pedal to run the machine and keep the program running in a loop.

The test machine can only be used for idle operation of the machine and cannot be used for processing!

7、 Principle Introduction:

No load, power on, press the motor start button, the motor works, the indicator light button lights up, the oil pump works, filtered, draws oil from the oil tank, and returns to the oil tank through the overflow valve

Pinch pipe - bend pipe - clip out - film transfer back - bend out - film transfer in - empty load state

8、 Debugging and mold installation

Fill up the mailbox with fuel

Connect to 380V power supply

Press Start

According to the corresponding actions, various actions can be executed

When manually bending the pipe, stop bending at the first set angle (convenient) for mold testing

Oil cylinders with sensors, regardless of whether the manual key is pressed or not, stop operating when there is a signal from the sensor

When performing clamping and bending operations, the auxiliary push must be retracted (there will be corresponding prompts at the bottom of the screen)

Adjust the overflow valve to make the system pressure appropriate

9、 Fault analysis