Tube plate fillet weld rod anodeXX-ray machine

Tube plate fillet weld rod anodeX-ray machine tube: RTW from Germany; Generator: German IMS

1： Product model and specifications

Tube plate fillet weld rod anodeX-ray machine MCTS

2： Product technical parameters and accessory list:

1. Technical parameters:

1. Scope of application: Pipe inner diameter greater than 15-50mm; Thickness of 0.8-6mm; Take a photo of the butt weld of the tube sheet with a distance of less than 35mm from the focal point to the end corner weld of the tube sheet.

1. Maximum power:104W

2. Maximum pipe high pressure:0～130KV

3. Maximum tube current:0-0.8mA

4. Focus size:0.5mm；

5. Target angle:168°x 360°

6. Protection distance:1m

7. Defect detection capability:0.5mm hole

2. Product supply list.

3： Introduction to product performance, working principle, etc

1. One X-ray high-voltage generator

The system is equipped with an imported lightweight rack mounted high-voltage generator, which adopts epoxy resin solid insulation packaging technology to seal the high-voltage components in a small container. It has an oil-free design, small volume, light weight, and easy mobility. High voltage power supply can provide the highestHigh voltage of 160KV, with a maximum power of 320W. The circuit system includes a resonant high-frequency inverter equipped with a patented control device, ensuring fault free operation in extreme transient processes and arc environments. The system also has an automatic current and voltage overcurrent protection system.

Main parameters:

Input voltage:90-250VAC，48-65Hz

Output voltage:5-160KV (limited to 130KV use)

Output voltage ripple: set value1%, after preheating

Voltage ripple: less than0.1%

Output current:2.0mA (limited to 0.8mA usage), with constant power mode

Output current ripple: set value0.1%, after preheating

Maximum power:320W (limited to 104W usage)

Output interface:160KV taper plug

Digital control interface: Ethernet

Cooling device: internal fan

Weight: Approximately34kg

External dimensions:40.1cm (length) x 49.4cm (width) x 18.2cm (height)

1. Rod anode1 set of X-ray tube

   2.1 One imported X-ray tube

Configure GermanyThe RTW dedicated radiator tube plate butt weld inspection rod anode ray machine has a maximum tube voltage of 130KV, a maximum tube current of 1.66mA, and a maximum power of 150W. It can replace the Ir192 gamma ray source for film photography and obtain clearer film images. The main specification parameters are as follows:

Anode target material: tungsten

Focus size:0.6mm testing0.5mm defect, refer to the official website standard

Target angle:168°x 360°

Filter element: 2.8mmAL

Filament voltage:5.0A

Filament current:3.5V

Environmental temperature:-10℃-40℃

Cooling method: conductor heat transfer cooling, maximum allowable temperature70℃

Rod anode length:37mm

2.2 Rod anode heat dissipation protection shell 1 set

The anode heat dissipation protective sleeve is made of lightweight aluminum alloy material with good thermal conductivity and high strength. Wrap the rod anode and radiation tube casing as a whole to enhance the strength of the rod anode and expand the heat dissipation area.

1. High voltage cable1 set

High voltage cable1 piece

1. The high-voltage generator is connected to the anode of the rod using a high flexibility, ultra small diameter cable imported from Germany3-core rubber insulated high-voltage cable, with R24 tapered rubber plugs connected at both ends. One end is bent at a 90 degree angle to ensure that the high-voltage cable section is not easily damaged. The cable length is 10m.

2. Flange plate2 of them

The connection and fixation method between high-voltage cables, radiation machines, and radiation tubes is flange fixation. Aluminum alloy material.

1. Remote control unit

   4.1 One laptop computer

4.2 Connect one data cable

A dedicated data cable for connecting a high-voltage power supply to a laptop,30 meters for remote control.

4.3 One set of radiation control software

The control software for the X-ray machine is specifically developed for this system based onWindows

Controller, connected to computer, can remotely preheat the pipe headKV、mA、 Setting operating parameters such as exposure time and power, as well as displaying fault codes and querying operation logs.

The software operates through a user-friendly graphical interface or directly inputs predetermined values for execution, with complete functions and convenient operation.

1. Aluminum alloy transport box1 piece

Customized aluminum alloy transport boxes are made of aluminum alloy material as the skeleton,ABS、 A box made of panels such as MDF (medium fiber board) and plywood (multi-layer board), combined with accessories such as tees, mouth strips, handles, locks, etc., has the characteristics of light weight, load-bearing capacity, strong and durable, and beautiful appearance. Configure one aluminum alloy instrument box in the system to store equipment by category.

The interior of the box adoptsEVA foam shock-absorbing foam and egg shell sponge are glued together. The shock-absorbing foam is grooved and glued according to the external dimensions of the stored goods, which facilitates equipment storage and has good seismic performance.

External dimensions of the box:80cm (length) x 80cm (width) x 40cm (height)

bearing:65kg