HH-4 separately controlled warm water bath pot

separateDigital constant temperature water bath: Each chamber is separated separately, with a separate digital constant temperature display. It is manufactured in one piece, with exquisite appearance and easy use!

This product is a sink type,Maximum aperture of mouth surface12centimetre,Four circles and one cover per hole,The inner pot is made of imported stainless steel and formed into shape,The shell is made of high-quality thin plate and sprayed with plastic,Electric heating tube installed in the middle of water,Heating up quickly,Energy saving,And equipped with a digital constant temperature device,Adjustment range,At room temperature -100°C,error±0.5°C.

1： Usage

a)Water must be added to the pot before use,Connect the power again.Set temperature:pressSETThe key can be used to set or view the temperature setpoint,clickSETThe characters on the digital display start flashing, indicating that the instrument panel has entered the set state. PressΔThe key setting value increases, press▽The key setting value decreases, long pressΔKey or▽The key data will change rapidly, once againSETThe key instrument panel returns to normal working state and the temperature setting is completed.

b)Front volume setting:pressSETkey3The second meter enters the inner parameter setting state. The first parameter that appears and flashes isEOOThe advance amount for stopping heating should be adjusted carefully. To reduce temperature overshoot, the instrument will control the heating output to cut off heating in advance. When the temperature drops below the advance amount, heating will resume and output within the set value and advance amount range(relay)It does not act, which can reduce the number of relay actions and extend the lifespan of the relay. Example: If the set value is50℃The advance quantity is0.5The instrument controls the heating to49.5℃When the relay is released, the temperature drops to50.0℃-0.5℃The relay is closed again. The larger the advance amount, the fewer times the relay will act. If the advance amount is too large, it will reduce the accuracy. After adjusting the advance quantity parameter, pressSETkey3The second meter returns to normal working condition.

c)Correction of errors:When confirming that the value displayed on the instrument is not the correct measurement value, the displayed value can be adjustedCorrection.pressSETkey3Enter the inner menu of the instrument panel in seconds,. The first parameter that appears and flashes isEOOPress the advance quantity againSETThe parameter where the key appears and flashes is the error correction parameterΔperhaps▽The key can modify this parameter. The range of error correction is-9.9℃arrive+9.9℃After the correction is completed, click againSETPress the key to exit. The correction value of the instrument when it leaves the factory is0.0When using, it is necessary to prevent correcting instruments that display correctly to incorrect ones.

Do not add too much water to the pot,To prevent water from spilling out of the pot when boiling,And it should be noted that the water in the pot should not expose the electric heating tube to the water surface,To avoid burning out the electric heating tube,Causing water leakage.

2： Precautions

(1)To ensure safety,Please connect the ground wire when using.

(2)Strictly prohibit not adding water,Dry burn.

(3)When not working,The power should be cut off,To prevent accidents from happening.

3： Purpose:

Electric constant temperature water bath pots are widely used for distillation, drying, concentration, and impregnation of chemical or biological products.

4： Type

Independently separate heating, constant temperature and temperature control

Heating:4Hole:4x300W

Temperature control range: room temperature-100℃±0.5℃

Temperature control method: digital display temperature control

Heating power:4Hole:1200W

Working size: 4Hole: （160*160*130）x4

Dimensions: 900x370x320mm

Regarding instrument customization and reservation:
Customers who need to customize instruments must provide specific technical parameters and requirements in writing and fax them to the company. After both parties reach a consensus and sign and approve each other, our company can produce the instruments. 60% of the deposit must be paid in advance for customized instruments. Due to the special nature of the instruments, necessary parameter and functional testing needs to be carried out before leaving the factory. Only instruments that have been successfully tested can be sent to you from the factory. Therefore, these instruments need to have a delivery date. If there is a delay of 2-3 days due to delayed or out of stock reasons, please understand.