Product characteristics

Wide chemical compatibility, high flow rate, low pressure difference, and long service life;

The filtering accuracy range is wide from 0.2 μ m to 60 μ m;

U adopts hot spinning melting process, which is firm and free of released substances contaminating the product;

U can be cleaned using ordinary methods and sterilized with high-pressure and steam sterilization;

Three layer filter material with high filtration accuracy (Absolute rating of 95%) for the filter element;

The filtering area is greater than 0.6-0.7m2, the pressure difference is low, the pollutant capacity is large, and the service life is long;

Made of 100% pure polypropylene material with high chemical resistance;

Production in a dust-free environment, with high cleanliness of the filter element;

U 18M - Ω DI water/2 GPM cleaning for 30 minutes, TOC content below 40PPb

The U-end cap and joint are sealed by hot spinning without the use of adhesive

The size of the U-joint and the material of the O-ring fully comply with international standards

application

Pre filtration of reverse osmosis water system and pre filtration of deionized water system.

Filtration of beverages, beer, mineral water, etc.

Filter organic solvents, inks, etc.

Filtering of pharmaceuticals, biological and plasma products, compressed air and gas filtration.

Filtering of electroplating solution, metal cutting fluid, photosensitive resist, and magnetic media, etc.

The pre filter element of the U R.O membrane is used to extend the service life of the RO membrane.

Pre filter for U DI Water system

Cooling water system filtration (PCW)

U medium low viscosity chemical industrial fluid filtration

Main technical parameters

Filtration

0.2 μ m, 0.45 μ m, 1 μ m, 3 μ m, 5 μ m, 10 μ m, 30 μ m, 60 μ m

filter area

0.60～0.70m2

Length (inches)

5"，10"，20"，30"，40"，

filter media

100% polypropylene melt blown ultrafine fiber

Material of central pillar and outer cylinder

High strength polypropylene

Gasket material

Buan N, Silicone resin, synthetic rubber,

Continuous work pressure

0.42Mpa at25℃

Backpressure difference

△P 0.28Mpa at60℃

work

temperature

88℃,0.28 Mpa; 60℃, 0.42Mpa

disinfection temperature

Disinfection cabinet at 120 ℃, 0.1 Mpa; steam: 134 ℃, 30 minutes

Product characteristics of PTFE polytetrafluoroethylene

Polypropylene non-woven fabric (extruded mesh) inner and outer support layers, polypropylene outer cover, center column and end cap, double O-ring seal. The filter element adopts hot melt welding technology

◆ Forming, without introducing adhesive, no foreign objects falling off. The filter element has undergone rigorous integrity testing

Uniform pore size distribution, high porosity, and large filtration area. High filtration efficiency, high flux, and low protein adsorption rate

◆ Has strong flexibility and strong interception ability. Good chemical compatibility and wide applicability

application

◆ Sterilization and filtration of compressed air, bioreactors, storage tanks, and ingredient tanks, as well as sterilization and filtration of high-purity gases and organic solvents in the electronics industry

Main technical parameters

Filtration

gas

0.02μm， 0.05μm

liquid

0.1μm， 0.22μm，0.45μm，1.0μm

Filter cartridge length

5"，10"，20"，30"， 40"

Filter diameter

Φ69mm

Filter area/10 "length

0.65m2 [10 "], 1.30m2 [20"], 1.95m2 [30 "], 2.60m2 [40"]

operation temperature

90 º C (at a pressure difference of 0.2MPa)

Working pressure

4.0MPa@25 ºC

Positive voltage difference

0.4MPa@25 ºC

Reverse voltage difference

0.3MPa@25 ºC

Steam

121 ± 2 º C, 30 minutes each time

Interface type

226 card in type

O-ring material

Fluororubber, Silicone Rubber

The melt blown filter cartridge is made by hot-melt entanglement of polypropylene ultrafine fibers, which immediately form a three-dimensional microporous structure in space. The pore size of the micropores is distributed in a gradient along the flow direction of the filtrate, integrating surface, deep, coarse and fine filtration, and can intercept impurities of different particle sizes. The precision range of the filter element is 0.5-100 μ m, and its flux is more than 1.5 times that of the same precision peak room filter element. Different types of end cap joints can be configured to meet the needs of various engineering installations.