dryer

characteristic

All areas in contact with the raw materials are made of stainless steel material

Equipped with a feeding port cover for easy installation of the suction machine

Adopting the principle of "hot air blowing down and air whirlwind exhaust" to ensure uniform and uniform drying effect

Purchase and equip with a seven day timer for automatic timed power on/off

Adjustable overheat safety protection device

Standard external insulated main power supply

Circuit design that complies with CE safety standards

Stee Hopper Dryer

Features

All parts contacting with raw material is made of stainless steel

A material nl liet cover is equipped , which is easy for installation of suction machine

With principles of Hot Air Down Blowing and Whirlwind Air exhausting h , te drying effect is ensured as even and uniform

A7-day timer is optional for automatic timing switch

Adjustable overheat safeguard devices

Standard external isulated master power supply

Circuit design meeting CE safety standards

Choose to install accessories

Unloading seat, magnetic frame, suction box, hot air recovery system, A-type tripod, L-shaped tripod, cut-off suction box

Optional Accessories

1: unloading seat 2: magnetic stand 3: suction box 4: hot air recycling system 5: A-type tripod 6: L type foot stand 7: broken material suction box

Box type dryer

characteristic

Adopting electronic temperature control to provide precise and uniform drying effect

High temperature sealed door opening to maintain consistent temperature and reduce power loss

Stainless steel discs can eliminate the drawbacks of raw material contamination caused during the drying process

Convenient maintenance design

Adjustable high temperature protector

Attached Ampere Meter

24-hour timer device

Adjustable air door opening

Motor overload protection

Main power switch

Adopt electronic temperature control

Provide precise dry-up function High-temperature fully-closed door can ensure constant temperature and reduce electrical consumption

Stainless steel can exclude the disadv-antages of the raw material contamination

Convenient design and maintenance

Adjustable temperature protector

The accessory includes ammeter

24H timer device

Adjustable air valve

Motor over-load protection

Power switch

1. Recycle motor

2. Multi wing wind turbine blower

3. Air room

4. Air inlet

5. Stainless steel trays

6. High temperature resistant insulation rock wool Asbestos cloth

7. Paint coated steel sheets

8. Plate spacer

9. Air outlet

10. Electric heating tube heater

working principle

There are movable plates in the box dryer, and the raw materials to be dried are placed inside the plates. During operation, the windmill forces air to pass through the electric heating tube, then through the partition wall with many small holes, and evenly blows in the raw materials. After the raw materials are evenly dried, the humid air is discharged from another wall opening

Working Principle

Place material on the movable trays; start the switch on power and machine starts to operate , strong wind wheel activated will blow air from the air inlet into the electric heating tube , hot air goes through the pored separated wall , and blows evenly on the material , moisture will be expelled by the dehumidification blower on the top . Moisture is expelled and material is dried through repeated process

Scope of application

The box dryer is suitable for drying all types of polymer materials and can simultaneously dry different materials. It is very suitable for a variety of raw materials or for use during mold testing. It can also be used for preheating or drying of agricultural products (pollen, garlic, tea) or related products in multiple industries such as electronics, motors, ferries, pharmaceuticals, baking paint, printing, etc

Application scope

The dry-up machine can be applied for the dry-up of all kinds of polymers . It also can dry up different kinds of materials . It is suitable for the dry-up of little and different materials e .g .powder , garlic and tea etc . It can be used for the dry-up/warm-up operation for the products in the fields of electronic , electric machinery , galvanization , pharmacy , baked enamel and printing industries

Dehumidification dryer

What is a honeycomb ceramic dehumidifier wheel

The honeycomb ceramic dehumidification wheel is formed by using ceramic Rowe as the substrate to form a honeycomb wheel, and then using a special chemical synthesis two-stage crystallization method to uniformly crystallize the moisture absorbing agent silica gel and molecular sieve on the ceramic Rowe wheel, giving it extremely strong moisture absorption ability. This structure of the wheel does not produce powder during operation and greatly extends its service life. After the humid air passes through countless micropores (moisture absorbing agent) in the honeycomb dehumidification wheel, the moisture is effectively absorbed. The air filtered and separated by the dehumidification wheel is removed from the bottom and dehumidified, becoming ultra-low dew point dry air. Regeneration is also carried out under the same principle, except that the direction of the honeycomb dehumidification wheel (moisture absorbing agent) is opposite

Dehumidifier Series

What’s the cellular ceramic desiccant wheel?

Desiccant wheel cellular ceramic substrate is formed of ceramic fiber honeycomb wheels , then the use of special methods of chemical synthesis of two crystals , the hygroscopic agent silica gel and molecular sieve crystals evenly on the wheel in the ceramic fiber , it has strong moisture absorption capacity . The structure of the wheel will not have powder in the run-time and significantly longer service life . Moist air through the desiccant wheel in numerous cellular micro (hygroscopic agent ), the moisture is effectively absorbed by the desiccant wheel out of the air filter was completely isolated after a low dew point dehumidification dry air . Regeneration is carried out under the same principle , only through the honeycomb desiccant wheel (hygroscopic agent )in the opposite direction

When to use a dehumidifier

Poor molding of plastic products is mostly caused by poor dehumidification and drying. The American Plastics Association requires that plastic before molding must be dried to a moisture content of less than 0.02%, with poor transparency, filter adhesion, burrs, bubbles, seals, flow marks, cracking, poor dimensional stability, internal pressure, and insufficient physical strength of the product. Most of the reasons for these defects are due to insufficient dehumidification and drying of the plastic before molding, especially for high immersion plastics such as PET, PBT, PA, PC, which require ultra-low dew point DEW POINT -40 ℃ drying equipment

Under what circumstances to use dehumidifier?

Plastic molding bad , most from dehumidification drying bad . American Plastics Association recommends that pre-molded plastic must be dried to a moisture content below 0.02% , poor transparency , runner stick , flash bubbles ,draw bar ,flow marks ,cracking , poor dimensional stability ,resulting in stress, product properties such as strength , weaknesses , most of its bad reason ,is mot fully formed before plastic due to dehumidification drying Particularly high , such as immersion of plastic : PET ,PBT ,PA , PC , etc. need low dew point Dew point -40 ℃drying equipment

Dehumidification dryer accessories selection

24-hour reservation timer

Can set timed power on and timed power off

Dew point detection display, optional: A randomly installed B portable

Oil filter

When plasticizers are present in the dry raw materials, an oil filter must be used

Cyclone dust collector

Suitable for PET dust removal systems with high levels of dust

Red double-layer silicone air duct

Touch based human-machine interface

Adopting PLC control combined with human-machine interface

Optional Accessories

24H reservation timer ( you can set start time and time off )

Dew point detection display ( Optional : a .b . Portable random mount )

Oil filter (When the dried material contains plasticizer oil filter to be used )

Cyclone dust collector : with photos (PET more suitable for dust removal system )

Red double-decker silicone duct

Touch man-machine interface : with photos (PLC control with man-machine interface )

Dehumidification, drying and feeding three machines in one

The ADS series dehumidification, drying, and feeding machine is a new product developed based on the actual situation of the plastic industry. The machine adopts a unique multi-stage honeycomb wheel, a stainless steel double-layer bottom blowing insulation hopper, a Taiwanese made feeding fan, and well-known electrical components such as Siemens from Germany, Omron from Japan, and Mitsubishi from Japan. Due to the centralized dehumidification, drying, and feeding of the machine, it has the advantages of fast and simple feeding, compact structure, and durability in plastic production, ensuring quality and fully demonstrating the perfect physical properties of plastic in plastic molding, thereby enhancing competitiveness

Desiccant Feeding Three In One

ADS series desiccant feeding Three in one , a combination of the actual situation of the plastics industry developed new products , The machine uses a unique multi-stage honeycomb wheels , stainless steel double blow insulation under the hopper , feeding fans from Taiwan , Siemens , Omron , Mitsubishi and other brands of electrical components . Concentration due to aircraft dehumidification , drying feeding on to three machines in the production of a plastic material for quick and simple , compact , rugged , etc ., let you in the plastic molding , plastic to ensure perfect quality and full of physical properties and thus enhance competitiveness

characteristic

Integrating two-stage feeding, dehumidification, and drying functions, but each control can be operated independently

Japanese imported microcomputer P I. D automatic adjustment, can automatically control the operation of the whole machine

24-hour automatic timer can be set to turn on and off at a predetermined time (optional)

Unique downward blowing double-layer hopper design to prevent heat loss and save energy

Closed loop feeding system to prevent the dried raw materials from getting damp again due to contact with external air

Compact structure, small footprint, easy to move

Automatic fault protection function, low failure rate, easy maintenance

This machine is suitable for engineering plastic materials with strong moisture absorption, such as PA, PC, PBT, PET, etc

Features

Set Sec feeding , dehumidification , drying function as a whole , but the control can operate independently

Japan imports Microprocessor P.I.D automatic control , automatic control of machine operation

24-hour automatic timer to turn off the scheduled time (Choose)

Double Blow unique hopper design , to prevent heat loss and save energy

Closed loop feeding system , to avoid drying of raw materials due to exposure to outside air and then wet

Compact , small footprint , easy to move

Fault protection , low failure rate , easy maintenance

The machine is suitable for highly hygroscopic materials such as engineering plastics : PA , PC ,PBT ,PET and so on