Detailed information on the dosing mixer and the folding paddle mixing mixer

Dosing mixer, paddle mixer, ZJ-1200 paddle mixer prices

Structure and working principle of the dosing paddle mixer and paddle mixer:

The paddle mixer system is a system that utilizes a dosing mixer and a reaction tank. The paddle mixer dosing mixer consists of a motor, a cycloidal gear gearbox (with a cycloidal gear set inside), a mixing shaft, and mixing blades. When the motor is powered, it drives the mixing shaft and mixing blades to rotate; By rotating the dosing stirrer to drive the water flow in the reaction tank, the reagents and water in the reaction tank are fully reacted, shortening the mixing time between the reagents and water and greatly improving the efficiency of the use of the reagents.

Features of the dosing mixer and the folding paddle mixing mixer:

1. It has a wide range of applications and can stir various liquids with different concentrations, media, and suspended solids.

2. Stable operation, low vibration, and low noise.

3. Corrosion resistant, therefore it can stir various liquids with pH 3-10.

If the equipment is not in use temporarily, it can be stored for a long time.

precautions：

The dosing mixer needs to be installed and used correctly to ensure safe and stable long-term operation.

Installation personnel should have corresponding qualifications and be familiar with mechanical equipment installation knowledge to carry out installation work.

The dosing mixer should be installed vertically, with a vertical deviation of no more than 5 degrees.

4. It is strictly prohibited to mix solids and liquids with high viscosity in the dosing mixing system.

5. The motor and bearing temperature cannot operate above 75 ℃.

The motor, bearings, and gearbox cannot operate in the absence of lubricating oil.

7. The agitator shaft and blades cannot operate under bending or deformation conditions. If the shaft is found to be bent or the blades are deformed, the machine should be stopped immediately for processing or replacement.

During the operation of the dosing mixing system, it is strictly prohibited to allow debris to enter the reaction tank to avoid damaging the mixer shaft and blades.

If a person needs to enter the reaction tank for cleaning or maintenance operations, the motor power must be cut off and a "Do Not Close" warning sign must be hung. When conducting manual tank cleaning and maintenance operations, there must be a dedicated person outside the reaction tank to supervise.

After running for a period of time, if there are sediment, impurities, and debris at the bottom of the reaction tank in the 10 dosing mixing system, it should be stopped in time and rinsed with clean water or manually cleaned to ensure the safe operation of the mixer.

Selection Notice

Parameters required for selection: flow rate, head, motor power

When inquiring, please provide: motor power, impeller diameter, and whether a system needs to be installed

Mixing of hard, lightweight aggregate concrete and various mortars and mortars.

Technical Literature:

The difference between bottom installation and side installation of paddle mixer

What are the differences between the bottom installation and side in installation of paddle mixers?

Foldable paddle mixerBottom mixing installation of this type of mixing equipmentThe mixer is installed at the bottom of the container. It has the characteristics of short and thin shaft, no need for intermediate bearings, and can use mechanical seal structure. It has the advantages of easy use and maintenance, long service life, etc. In addition, the agitator of the paddle mixer is installed at the lower head, which is conducive to the arrangement and installation of accessories at the upper head, especially when the upper head is equipped with a jacket, cooling components, and connecting pipes, which is more conducive to the overall rational layout.

Paddle mixer side entry mixing installation Side entry mixing equipment is to install the mixer on the side wall of the container body. This consumes the same amount of powerThe paddle mixer can achieve the best mixing effect. The speed of this mixer is generally 360450r/min, and there are two driving methods: gear transmission and belt transmission. The main disadvantage of the equipment is that it is difficult to seal the shaft.

In addition to the two different types of agitators mentioned above, paddle mixersThere are other types of mixers available for installation. For example, a horizontal container mixer is installed above the horizontal container. This layout can reduce the installation height of the entire equipment, improve the anti vibration ability of the equipment, and improve the suspension state. For example, a horizontal container mixer is used for inflatable mixing.

Technical parameters for the design requirements of paddle mixers and characteristics of starch mixing processingBy comparing the characteristics of the above mentioned mixing installation types, the eccentric mixing installation type is selected, and the driving method is deceleration transmission. The mixer designed in this article mainly consists of the following parts: AC motor, coupling, transmission device, mixer, lifting mechanism of mixing tank, control circuit, and lubrication and sealing device.

Jiangsu Du'an Environmental Protection Folding Paddle Blender Wire Connection Method:
a) Four core wire: Three core thick wire is the three-phase live wire, and one core wire with yellow/green dual color is the ground wire.
b) Five core wire: The three core thick wire is the three-phase live wire, the one core wire is the yellow/green dual color ground wire, and the one core wire is the 31 # wire (motor leakage signal wire)
c) Seven core wire: The three core thick wire is the three-phase live wire, the one core wire is the yellow/green dual color ground wire, the one core wire is the 31 # wire (motor leakage signal wire), and the other two core wires are the 11 # and 12 # wires (motor overheating protection signal wire)