The electronic component moisture analyzer produced by Yienda uses a heating unit and a moisture evaporation channel to quickly dry the sample. During the drying process, the moisture analyzer continuously measures and displays the percentage of moisture lost in the sample in real time. After the drying program is completed, the final measured moisture content value is locked and displayed. Compared with the international oven heating method, circular heating can reach the maximum heating power in the shortest time, and the sample can be quickly dried at high temperatures. Its detection results have good consistency with the national standard oven method, are replaceable, and the detection efficiency is much higher than that of the oven method. Generally, the sample can be measured in just a few minutes. And the operation is simple, the testing is accurate, and the display part adopts LED digital tubes, which can display data such as moisture value, sample initial value, final value, measurement time, temperature initial value, final value, etc., clearly visible.

• Model:	YD-100S
  Measurement range:	0.0001-120g
  Range of moisture content determination：	0.001%－100%
  Determination range of solid content	100%－0.001%
  Readability of moisture content:	0.001%
  heating temperature：	40－200℃
  show contents：	Moisture content, solid content, time, temperature, weight
  Display mode:	Equipped with backlight sourceLCDLCD display screen
  The weighing sensor：	Imported sensors from Germany to ensure measurement accuracy
  Temperature sensor	high-precisionPT100Platinum thermistor
  Using power supply:	Voltage220v±10%frequency50HZ±1HZ
  Weighing tray size:	diameter90mm
  Working environment temperature：	5℃－35℃ is optimal

• 
  
  
  
• 
  
• 
  

  Product advantages;

  1. Visual operation can clearly observe the changes of the product under high temperature;

  2. Zero consumables, replacing the expensive consumables (sample tray) cost of traditional moisture meters in the later stage

  3. Adopting electromagnetic balance force weighing sensors imported from Germany, with high accuracy, long service life, and stable performance;

  4. The heating method of halogen ring lamp can directly heat the material from the inside, while heating the edges and middle of the material evenly;

  5. Double layered glass design creates a balanced cycle and real-time monitoring of moisture loss, resulting in more accurate results;

  6. After the fully automatic measurement is completed, an alarm reminder will be given, and the measurement process does not require supervision;

  7. Real time curve display, visually observing changes in moisture content;

  8. Advanced humidity control system to avoid interference caused by free moisture;

  9. The moisture and solid content of the sample can be converted and displayed simultaneously;

  10. The heating chamber adopts a pure stainless steel chamber cover, which is heat-resistant and easy to clean;

  11. Communication interface: RS232 interface, can be connected to a printer;

  Attachment list;

  ① One moisture tester mainframe, one windproof disk, one sample disk bracket, one sample disk bracket, two sample disks (stainless steel), six weights, one instruction manual, one product certificate, and one power transformer

• 　　
• The testing of the moisture meter involves the following steps:

  1. Set the heating method

  2. Set the heating temperature

  3. Set shutdown mode (shutdown time, automatic shutdown weight loss rate)

  4. Prepare test samples

  4.1 Place the empty sample tray on the tray holder,

  4.2 Press the 'Peel' button to remove the weight of the sample tray

  4.3 Remove the sample tray and place the sample, preferably larger than 0.5g

  4.4 Uniformly distribute the samples on the sample tray

  4.5 Place the sample tray containing the sample back onto the rack, and the display screen will show the weight of the sample

  5. Close the heating chamber

  6. Press the [Start] button to start measuring

  7. The display screen shows the current weight value. Press the [Unit Conversion Key] to convert the current measurement result

  8. After the measurement is completed, the display screen shows the final moisture content of the sample. Press the [Peel] button to return to normal weighing mode

  9. Press the 'Print' button to send the current measurement result to the printer or other peripheral device.

  Note: At any time during the testing process, you can press the 'Stop' button to terminate

• 
  

  • One year free warranty, lifetime maintenance;

    7-day no reason return and exchange, 24-hour instant response;

    One on one technical guidance, allowing you to have no worries after purchasing;

    National free consultation hotline: 18659285958

  • 

Data Download	Update Date
Electronic component moisture analyzer	2015-08-20
Instruction manual download	Update Date
Electronic component moisture analyzer	2015-08-20
Color page download	Update Date
Electronic component moisture analyzer	2015-08-20

• 

• Option 1: Customer ------->Business Manager ------->Contract Signing ------->Payment on Delivery ------->Corporate Transfer ------->Warehouse Shipment ------->Confirm Receipt ------->Our Company Invoices

  
  

  Option 2: Customer ------->Business Manager ------->Contract Signing ------->Cash on Delivery ------->Warehouse Shipment ------->Express Collection ------->Confirm Receipt ------->Our Company Invoices