Multi functional non-destructive testing instrument TLS-601V | crack detector | defect detector

1、 Product Features
1. Defect detection: This instrument is suitable for detecting cracks on the surface and inside of workpieces, as well as other defects such as pores and inclusions.
2. Steel grade testing for steel components. Suitable for mixing and steel grade identification of various grades of steel raw materials.
3. Hardness testing: The actual hardness value can be detected based on the standard sample.
4. Carbon testing. The actual carbon content can be detected based on the standard sample.
2、 Product features:
1. Can be used for both AC and DC. The machine is equipped with an automatic charging device.
2. The instrument can be used for on-site and outdoor testing in any factory by charging the DC battery inside.
3. This product does not require preheating or plug in for immediate use. The product does not generate heat during use.
4. Multiple digital displays. Clear and concise.
5. Small in size, lightweight, and easy to carry.
6. Fast detection speed, reaching 1000 pieces/hour.
7. Non destructive testing requires no contact between the instrument and the surface of the workpiece, and does not damage the tested workpiece. Convenient online inspection, conducting full inspection of components instead of random sampling.
8. Strong intuitiveness, while displaying measurement results using numbers or pointers.
9. The instrument has no requirements for the surface roughness of the tested workpiece, and can detect workpieces containing oil stains, rust, or oxide layers without affecting the detection results.
3、 Detection range
Suitable for non-destructive testing of various steel parts, alloys, non-ferrous metals, aluminum alloys, copper alloys, and other materials, including plates, rods, tubes, wires, strips, billets, and various shaped steel materials and components. Workpieces ranging from several meters to one millimeter can be tested.
4、 Detection accuracy
1. Crack (porosity, inclusions) detection: accuracy rate of 100%, no misjudgment.
2. Steel grade detection: accuracy rate of 100%, without any misjudgment.
3. Hardness testing: 1HRC or 10HB.
4. Carbon testing: 0.03% C.
5、 Hardness resolution
0.1HRC or 1HB
6、 Parameters
1. Probe: The diameter range of the probe is optional from 5 to 350mm, and pen probe or rectangular probe can also be selected.
2. Detection speed: 1000 pieces/hour
3. Working power supply
(1) 50HZ mains power, 220V+10% single-phase AC.
(2) In the absence of a power source, a DC power supply can be used, and the battery can work continuously for more than 12 hours on a single charge.
(3) The instrument consumes 3W of power and has a charging status of 7W.
4. Usage conditions
(1) Environmental temperature:- 20 ° C~40 ° C.
(2) Relative humidity:< 75%.
(3) When testing in the same batch, the dimensions and specifications of the tested workpieces should be the same
(4) High frequency impact and corrosive gases should be avoided when using electricity.
(5) Working hours: The instrument can work continuously without being limited by usage time.
5. Dimensions: 340 * 320 * 200mm
6. Instrument weight: 9kg
7、 Usage:
1. Crack (porosity, inclusion) detection:
Use qualified parts as standard samples. Collect data on cracked parts and compare it with qualified parts.
First, place a good and qualified workpiece into the testing probe, adjust the pointer of the instrument to the 0 position, and this is the standard sample made of a good workpiece; Next, place the remaining workpieces one by one into the detection probe. It can be seen that when the pointer points to the 0 position, it indicates that the workpiece is good and qualified. However, if the pointer does not point to 0 and floats very much after placing the workpiece into the probe, then the workpiece is considered unqualified.
2. Steel grade detection: Consistent with the detection method for cracks (pores, inclusions).
3. Hardness testing: First, use a workpiece with a known hardness value as a standard sample for testing. Adjust the instrument's display value to this hardness value, and then you can test other workpieces one by one, and the corresponding hardness values can be displayed.
4. Carbon testing: Consistent with hardness testing method.
This instrument belongs to the intelligent type and has functions such as data storage, analysis, and error prompts. The requirements for the operator are not high, even for first-time operators of this instrument, as long as they follow the operating instructions to operate the instrument, they can obtain the correct test results.
8、 Instrument configuration:
One non-destructive testing instrument
One set of standard probes
One fuse
One instruction manual
One power plug