Introduction to the Tian General Sorghum Seed planter produced by the Woye Agricultural Machinery Parts Factory in Renqiu City:
Main technical parameters of sorghum seeder:
1. Dimensions (length * width * height) with variable speed spoon wheel seeder: 277 * 274 * 260cm
2. Seed planter rows: single row
3. Seed planter type: single row
4. Quantity of spoons: 24 (and can be customized according to demand)
5. Suitable sowing speed: less than 5 kilometers per hour
6. Seed breakage rate: less than 2.5%

Internal diagram of sorghum seeder

Video display of Woye sorghum seeder:

1、 Dismantling method of seeding spoon wheel:
1. Put the remaining seeds in the empty box, 2. Cut off the transparent end cover, 3. Remove the 3 countersunk screws that fix the spoon wheel, and 4. Remove the spoon wheel,
2、 Installation method of spoon wheel:
1. Install the spoon wheel onto the seed guide wheel with 3 countersunk screws, so that the partition is sandwiched between the spoon wheel and the seed guide wheel. 2. Install the transparent end cover.
3、 Installation method of brush:
1. The brush is installed on the inner side of the transparent cover, and the groove on the brush matches the protrusion on the end cover.
2. Tighten the screws on the outside of the transparent cover
4、 Adjustment of seed planter handball:
Pull out the handball and slide it up and down to adjust the height of the seed inlet on the partition. The specific operation is as follows:
When the seed size is small, adjust the handball towards the direction marked with "small" on the end cap,
When the seed size is large, adjust the handball towards the direction marked with the word "large" on the end cap.
5、 Adjustment of plant spacing:
1. A spoon wheel seeder with a gearbox, which can adjust six plant spacing by moving the gear lever. The plant spacing gradually increases from 1st gear to 6th gear, and the seeder does not work when in neutral position and is in a clutch state,
6、 Oil filling method for seeders with gearbox:
1. Remove the dust cover labeled with numbers on the transmission cover,
2. Add an appropriate amount of butter or engine oil to the gears and shafts inside the gearbox
3. Install the dust cover.

Precautions for using General Tian's seed planter:

During use, the handball should be adjusted according to the different shapes and sizes of the seeds to lower or raise the position of the seed inlet on the partition to meet the sowing requirements,
2. Corn seeds need to be screened to remove large and small grains, as well as impurities in the seeds, in order to ensure the quality of sowing
3. The seed planter is equipped with a medium seed spoon wheel at the factory, which can only meet the normal needs of corn seeds. Users of extremely large and small seeds should purchase corresponding large or small seed spoons from distributors or seed planter manufacturers, otherwise it will seriously affect the sowing quality,
4. Coated seeds must be dried in the sun and mixed with 1% medical grade talcum powder before sowing to reduce adhesion. If too much talcum powder is mixed, excess talcum powder should be sieved out using a sieve.
5. After one shift of homework, check whether the rotating parts of the seeder are flexible, whether the fixing screws are loose, and clean the seed coating agent stuck on the spoon wheel, partition, and box with water or diesel. For seeders with a gearbox, remove the dust cover marked with numbers on the gearbox cover to clear the dust inside the gearbox. If not cleaned in time, it will cause bearing jamming and affect the sowing effect,
6. Seed planter with gearbox must not be reversed
7. The seeder is strictly prohibited from carrying seeds for long-distance transportation. If changing plots or transporting, the remaining seeds should be cleared and replanted upon arrival at the location,
8. When disassembling or sowing the spoon wheel, be sure to prevent weeds from entering the planter to avoid damaging the spoon wheel
9. The distance between the seeding point of the seeder and the ground should not exceed 150 millimeters. The matching and rotating parts should be coated with oil to prevent rust and placed in a ventilated and dry place.
10. After the homework is completed, the remaining corn seeds in the seeder should be cleaned, and the matching and rotating parts should be coated with oil to prevent rust, and placed in a ventilated and dry place,
11. If the plant spacing is less than 7 inches, the machine guided seeder inspection uses a spoon wheel with 18 spoons