Product parameters and features:

Combination pneumatic steel strapping machine (integrated tightening and locking)

Product Introduction:

The XGD-19/32 combined steel strapping machine is a new and advanced pneumatic packaging tool, mainly used for strapping various specifications of pipes, profiles, ingots, plates, and other products in non-ferrous metal and steel enterprises weighing less than four tons. Its characteristics are small size, light weight, compact structure, high work efficiency, strong adaptability, convenient use, safety and reliability. The whole machine can be replaced with seven types of parts, including 25mm and 32mm wide steel stripsstrap.

Product advantages:

1. Operated with a gas source, sturdy and durable, easy to maintain

2. Combination structure, integrating pneumatic tightening, biting, and cutting.

3. Double bite buckle type

4. Good stability

5. Fully pneumatic push button operation.

Technical parameters:

Width of steel strip used: 19~32 mm

Thickness of steel strip used: 0.9 mm

Buckle clamp bearing capacity: 19mm ≥ 10 KN; 32mm≥13 KN

Maximum speed of pneumatic motor: ≤ 13000 r/min

Rated power of pneumatic motor: ≤ 0.26 KW

Air consumption: 0.46 m3/h

Friction wheel speed: ≤ 45 r/min

Friction wheel tension: ≤ 6300 N

Running speed of strapping: ≤ 5.3 m/min

Completion time of one action: ≤ 15 s

Whole machine weight: 13.5 ± 0.4 kg

Dimensions: 400 × 250 × 380 mm

Product features:

1. Composite steel stripbalerThe integration of pneumatic tightening, biting, and cutting is completed.

2. Fully pneumatic operation, with high tightening force

3. Made with advanced technology, with good stability and performance

4. The combination packaging machine can use steel strips with a width of 25 or 32mm (choose one)

Operation, use and maintenance methods of pneumatic steel strapping machine

1： Precautions for use:

1. The baler can be hung horizontally or vertically on a rotatable and movable crossbeam through a balancer or heavy-duty spring, and can be positioned freely to provide a certain working space for the baler (note: the detachable type does not require a balancer or spring hanging device).

2. When using a packaging machine, combustible gases must never be used. The compressed air source must pass through an oil-water separator, pressure regulating valve, and oil mist device. It is best to use a 12mm outer tube and an 8mm inner tube to withstand a pressure of 0.9Mpa. The oil mist device should be filled with 22 # turbine oil and 60-100 # spindle oil.

3. The maximum working length of the trachea is 10 meters, and the ideal length is within 5 meters.

4. The normal working clearance under the pressure of the working friction wheel of the packaging machine is 0.1-0.3 millimeters.

5. Keep the various moving parts of the packaging machine lubricated.

2、 Equipment repair and maintenance: (If there is a malfunction, please refer to the following characteristics and analyze the cause to solve it)

1. Insufficient locking force.

A. Parts are worn or deformed and need to be replaced.

B. Foreign impurities entering the cylinder block hinder the movement of the piston on the surface of the cylinder block. The cylinder block should be disassembled, cleaned, and reassembled for use.

C. The piston cannot rebound, and there is a leakage in the directional valve, causing the actual working air pressure entering the sealing cylinder to be low. It is necessary to replace the pointed plug O-ring.

2. Insufficient tightening force.

A. The surface mesh of the feeding roller is worn and needs to be replaced.

B. The gap between the feeding pressure wheel and the cushion wheel is unreasonable and should be adjusted.

C. The blades inside the pneumatic motor are worn and need to be replaced.

D. The directional valve is leaking, causing the actual working air pressure entering the air motor to be low. The seal should be replaced according to the inspection results.

3. Insufficient cutting force.

A. Blade wear.

B. Check if the work pressure is normal.

C. The force to cut off the steel strip comes from the blocking cylinder, refer to the phenomenon in "Fault".

D. Check the blocking operation.

4、 Gas path inspection:

A. The air pressure shall not be lower than 0.4Mpa.

B. Insufficient gas supply, check whether there is oil pollution blockage or leakage in the gas pipeline.

C. Regularly check the filter and pressure regulator, and drain the accumulated water in the oil-water separator regularly.

D. Check if the amount of oil dripped from the oil mist device is appropriate. If there is a lack of grease, an appropriate amount of No. 22 turbine oil can be directly injected into the interior.

5、 List of vulnerable parts:

A. Friction wheel.

B. Cutting knife.

C. Tighten the block.

D. Complete set of sealing components.

E. Wind blades.

F. Rotary gear

Maintenance and upkeep of steel strapping machine

Due to the wear and tear of parts and the loosening of screws during the operation of the steel strapping machine, as well as the decrease in air source pressure, the steel strapping machine may experience malfunctions. Therefore, timely troubleshooting is necessary to ensure the smooth operation of the machine. There are several reasons for the malfunctions. If the maintenance and upkeep of the steel strapping machine are strengthened, it will greatly extend the service life of the machine.

1. Before each shift of use, an appropriate amount of lubricating oil must be injected into the pneumatic motor, cylinder block, and all transmission and rotating parts. In addition, the oil injector should be regularly and quantitatively filled with 22 # air wheel oil to maintain a fixed oil supply. When the pneumatic motor is working, the optimal oil drop rate from the injector is 40-60 drops/min.

2. When the compressed air does not reach 0.4-0.6Mpa, adjustments must be made. Otherwise, too low pressure will affect the quality of bundling, and too high pressure will cause the machine to wear out too quickly.

3. The oil injector and oil-water separator should be cleaned with kerosene every three months, and the accumulated water in the oil-water separator should be removed daily.

4. The gap between the friction wheel and the pad wheel should be between 0.5-0.7mm, otherwise it should be adjusted and the debris and dirt on the friction wheel should be removed in a timely manner.

5. Due to long-term wear and tear of parts, environmental pollution, and poor lubrication, faults may occur. Therefore, it is important to detect and promptly eliminate faults. The following inspections and repairs can be solved using universal tools. Mastering the following techniques will not cause downtime or loss of valuable time when shutting down the machine due to minor faults and seeking help from the manufacturer.

After sales service:

Free Consultation

Customer service engineers answer customer questions online, assist users in troubleshooting, and provide guidance on the correct usage methods.

Free warranty

The promotional products sold come with a one-year warranty for the entire machine, and vulnerable parts are not included in the warranty and will incur corresponding cost fees. The accessory company will send it to you by express delivery. If you have any questions, please contact us by phone or video. If you need on-site service, please contact customer service.

Regular follow-up visits:

The customer service of Shandong Xingpake will regularly visit customers by phone to understand the usage of the equipment and answer any difficult questions they may encounter in their daily lives. At the same time, absorb the opinions and suggestions of customers in using the equipment, in order to better serve customers in the future.

Kind reminder: Please read this manual carefully before operating this machine. We will provide an instruction manual for each machine, and any damage caused by personal operation errors will not be covered by the warranty.